Mitsubishi Outlander manuals

Mitsubishi Outlander: Dead Lock System

The Dead Lock System helps to prevent theft. When the keyless entry system has been used to lock all of the doors and the tailgate, the Dead Lock System makes it impossible to unlock the doors using the inside lock knobs.

CAUTION:

● Do not set the Dead Lock system when someone is inside the vehicle. With the Dead Lock system set, it is not possible to unlock the doors using the inside lock knobs. If you erroneously set the Dead Lock system, unlock the doors using the UNLOCK switch of the keyless entry system.

Setting the system

1. Turn the ignition switch to the “LOCK” position.

1. Turn the ignition switch to the “LOCK” position.

Also, if a key was used to start the engine, remove the key from the ignition switch.

2. Get out of the vehicle. Close all of the doors and the tailgate.

3. Press the LOCK switch (A) of the keyless entry system to lock all of the doors and the tailgate. The hazard warning lamps will flash once.

4. Press the LOCK switch (A) again within two seconds.

The hazard warning lamps will flash three times to show that the Dead Lock System has been set.

NOTE:

NOTE:

● Pressing the LOCK switch (A) once while the Dead Lock System is set causes the hazard warning lamps to flash three times, so it is possible to confirm that the Dead Lock System is set.

● It is Possible to alter the system’s functionality as follows:

• It is possible to disable the operation confirmation function (flashing of the hazard warning lamps).

• It is possible to change the number of times the operation confirmation function causes the hazard warning lamps to flash for confirmation of system operation.

For details, please contact a MITSUBISHI MOTORS Authorised Service Point.

Cancelling the system

When the UNLOCK switch (B) of the keyless entry system is pressed to unlock the

When the UNLOCK switch (B) of the keyless entry system is pressed to unlock the doors and tailgate, the Dead Lock System is simultaneously cancelled.

NOTE:

NOTE:

● If neither a door nor the tailgate is opened within 30 seconds of unlocking, the doors and tailgate are automatically relocked and the Dead Lock System is simultaneously set again.

● Even when it is not possible to use the keyless entry system to unlock the doors, it is possible to use the key to unlock a door. When the key is used to unlock a door, the Dead Lock System is cancelled for only that door. If you wish to subsequently unlock all of the doors, turn the ignition switch to the “ON” or “ACC” position.

● It is possible to adjust the duration after which automatic relocking takes place when the UNLOCK switch (B) has been pressed. For details, please contact a MITSUBISHI MOTORS Authorised Service point.

Testing the system

Open all of the door windows, then set the Dead Lock System (refer to “Setting the system”).

After setting the Dead Lock System, reach into the vehicle through the windows and confirm that you cannot unlock the doors using the lock knobs.

NOTE:

● If you need advice on how to set the Dead Lock System is difficult to understand, please contact a MITSUBISHI MOTORS Authorised Service Point.

READ NEXT:

 “Child-protection” rear doors

1- Lock. 2- Unlock. Child protection helps prevent the rear doors from being opened accidentally from the inside. If the lever is set to the locked position, the rear doors cannot be opened usi

 Split tailgate

WARNING: ● It is dangerous to drive with the tailgate (upper gate and lower gate) open, since carbon monoxide (CO) gas can enter the cabin. You cannot see or smell CO. It can cause unconscio

 Inside tailgate release

The inside tailgate release is designed to provide a way to open the tailgate in the case of a discharged battery. The tailgate release lever (see illustration) is mounted on the tailgate. You a

SEE MORE:

 Camshaft

REMOVAL AND INSTALLATION Removal steps Engine oil control valve (OCV) exhaust O-ring Engine oil control valve (OCV) intake O-ring Front camshaft bearing cap Oil feeding camshaft bearing cap Camshaft bearing cap Thrust camshaft bearing cap Bearing Camshaft intake Camshaft exhaust Bear

 Fender, Splash Shield, Fuel Filler Lid, Strut Tower Bar

Fender REMOVAL AND INSTALLATION Pre-removal and post-installation operation Splash shield front removal and installation Front bumper side bracket removal and installation Headlight assembly removal and installation Side turn-signal lamp removal and installation Front deck garnish removal a

© 2010-2022 Copyright www.mioutlander.com