Mitsubishi Outlander: To operate using the keyless operation function
Locking the doors and tailgate
When you are carrying the keyless operation key, if you press the driver’s or front passenger’s door lock/unlock switch (A), or the tailgate LOCK switch (B) within the operating range, the doors and the tailgate are locked.
The turn-signal lamps will blink once.
Also refer to “Locking and unlocking: Doors, Central door locks, tailgate” on pages 1-21, 1-22 and 1-26.
NOTE
• For vehicles equipped with the mirror retractor switch, the outside rear-view mirrors automatically retract when all the doors and tailgate are locked using the keyless operation function.
Refer to “Starting and driving: Outside rearview mirrors”.
• With a vehicle that has a Dead Lock System, pressing the driver’s or front passenger’s door lock/unlock switch (A), or the tailgate LOCK switch (B) two times in succession causes the Dead Lock System to be set. (Refer to “Setting the system”).
• The keyless operation function does not operate under the following conditions:
• The keyless operation key is inside the vehicle.
• A door or the tailgate is open or ajar.
• The operation mode is not in OFF.
Unlocking the doors and tailgate
When you are carrying the keyless operation key, if you press the driver’s or front passenger’s door lock/unlock switch (A), or the tailgate OPEN switch (B) within the operating range, all the doors and the tailgate are unlocked.
If the front room lamp switch is in the “DOOR” position or the rear room lamp switch (except for vehicles equipped with the sunshade) is in the middle (•) position at this time, the room lamp will turn on for 15 seconds. The turn-signal lamps will blink twice.
If the driver’s or front passenger’s door lock/unlock switch is pressed and any of the doors or tailgate is not opened within approximately 30 seconds, relocking will automatically occur. Also refer to “Locking and unlocking: Doors, Central door locks, tailgate” on pages 1-21, 1-22 and 1-26.
NOTE
• For vehicles equipped with the mirror retractor switch, the outside rear-view mirrors automatically extend when all the doors and tailgate are unlocked using the keyless operation function.
Refer to “Starting and driving: Outside rearview mirrors”.
• Except for vehicles equipped with a Dead Lock System, the keyless operation function can be set so that only the driver’s door unlocks when the driver’s door lock/unlock switch is pressed.
If the keyless operation function is set to work as described above, all the doors and the tailgate unlock when the driver’s door lock/unlock switch is pressed two times in succession.
Refer to “Setting of door and tailgate unlock function”.
• The keyless operation function does not operate under the following conditions:
• The keyless operation key is inside the vehicle.
• A door or the tailgate is open or ajar.
• The operation mode is not in OFF.
• The time between unlocking and automatic locking can be adjusted. Consult a MITSUBISHI MOTORS Authorized Service Point.
On vehicles equipped with MITSUBISHI Multi-Communication System (MMCS), screen operations can be used to make the adjustment.
Refer to the separate owner’s manual for details.
Operation confirmation when locking and unlocking
Operation can be confirmed as shown below. However, the room lamp will only illuminate if the front room lamp switch is in the “DOOR” position or the rear room lamp switch (except for vehicles equipped with the sunshade) is in the middle (•) position.
When locking: The turn-signal lamps will blink once.
When unlocking:
The room lamp illuminates for approximately 15 seconds, the turn-signal lamps blink twice.
NOTE
• Functions can be modified as stated below.
For further information, please contact your MITSUBISHI MOTORS Authorized Service Point.
On vehicles equipped with MITSUBISHI Multi-Communication System (MMCS), screen operations can be used to make the adjustment.
Refer to the separate owner’s manual for details.
• Set the confirmation function (blinking of the turn-signal lamps) to operate only when the vehicle is locked or only when the vehicle is unlocked.
• Disable the operation confirmation function (blinking of the turn-signal lamps).
• Change the number of blinks for the operation confirmation function (blinks of the turn-signal lamps)
Operation of the Dead Lock System
With a vehicle that has a Dead Lock System, it is possible to set the Dead Lock System using the driver’s or front passenger’s door lock/unlock switch, or the tailgate LOCK switch. (Refer to “Dead Lock System”.)
READ NEXT:
Electronic immobilizer (Anti-theft starting system)
The electronic immobilizer has been designed to significantly reduce the possibility
of vehicle theft.
The purpose of the system is to immobilize the vehicle if an invalid start is
attempted. A v
Engine switch
In order to prevent theft, the engine will not start unless a preregistered keyless
operation key is used.
(Engine immobilizer function) If you are carrying the keyless operation key,
you can sta
Warning activation
In order to prevent vehicle theft or the accidental operation of the keyless
operation system, the buzzer and the display on the information screen in the multi-
information display are used to al
SEE MORE:
Third seat (7 persons)
To fold out the underfloor-stowable third seat
The third seat is stowed under the floor. Use the seat when extra people ride
in your vehicle. When not in use, stow the seat under the floor and use as a luggage
area.
WARNING:
● Make sure that you arrange the third seat before starting to
Changing the time until “REST REMINDER” is displayed
The time until the display appears can be changed.
1. Press and hold the multi-information meter switch for about 2 seconds or more
to switch from the setting mode screen to the menu screen.
Refer to “Changing the function settings (when the ignition switch is “ON”)”.
2. Lightly press t
