Mitsubishi Outlander: Lamps (headlamps, fog lamp, etc.) auto-cutout function
• If the following operation is performed while the lamp switch is in the
position, the lamps will automatically
go out when the driver’s door is opened.
[Except for vehicles equipped with keyless operation system]
The ignition switch is turned to the “LOCK” or “ACC” position, or the key is removed from the ignition switch.
[For vehicles equipped with keyless operation system]
The operation mode is in OFF or ACC.
[When the engine was started using the key]
• If the key is removed and the driver’s door is opened, a buzzer sounds at a high pitch intermittently to remind the driver to turn off the lamps.
[When the engine was started using the keyless operation function]
If the operation mode is put in OFF and the driver’s door is opened, a buzzer sounds at a high pitch intermittently to remind the driver to turn off the lamps.
• If the following operation is performed while the lamp switch is in the
position, the lamps will remain on
for about 3 minutes while the driver’s door is shut and will then automatically
go out.
[Except for vehicles equipped with keyless operation system]
The ignition switch is turned to the “LOCK” or “ACC” position, or the key is removed from the ignition switch.
[For vehicles equipped with keyless operation system]
The operation mode is in OFF or ACC.
NOTE
• The lamp auto-cutout will not function when the lamp switch is in the
position.
• The lamp auto-cutout function can also be disabled.
For further information, we recommend you to consult a MITSUBISHI MOTORS Authorized Service Point.
On vehicles equipped with MITSUBISHI Multi-Communication System (MMCS), screen operations can be used to make the adjustment.
Refer to the separate owner’s manual for details.
When you want to keep the lamps on:
1. In the following cases, turn the lamp switch to the “OFF” position.
[Except for vehicles equipped with keyless operation system]
The ignition switch is in the “LOCK” or “ACC” position.
[For vehicles equipped with keyless operation system]
The operation mode is in OFF or ACC.
2. Turn on the lamps with the switch in the
position again, then the lamps will
remain on.
NOTE
• When the engine was started using the key, if the driver’s door is opened and the key is removed, the lamp monitor buzzer sounds at a high pitch intermittently.
The buzzer stops when the driver’s door is closed. (The warning is also displayed on the multi-information display.) The buzzer stops in the following manner.
• Turn the lamp switch to the “OFF” position.
• Close the driver’s door.
• When the engine was started using the keyless operation function, if the driver’s door is opened and the operation mode is put in OFF, the lamp monitor buzzer sounds at a high pitch intermittently.
The buzzer stops when the driver’s door is closed. (The warning is also displayed on the multi-information display.) The buzzer stops in the following manner.
• Turn the lamp switch to the “OFF” position.
• Close the driver’s door.
READ NEXT:
Lamp monitor buzzer
[When the engine was started using the key]
If the driver’s door is opened when the key is in the “LOCK” or “ACC” position
or removed from the ignition switch while the lamps are on, a bu
Dipper (High/Low beam change)
When the lamp switch is in the position,
the beam changes from high to low (or low to high) each time the lever is pulled
fully (1). While the high beam is on, the high-beam indication lamp in th
Headlamp flasher
The high-beams flash when the lever is pulled slightly (2), and will go off when
it is released.
When the high-beam is on, the high-beam indication lamp in the instrument cluster
will illuminate.
SEE MORE:
Rear room lamp
The room lamp can be turned on by sliding the room lamp switch.
1 (ON) - The room lamp goes on.
2 ( ) - The lamp illuminates when a door or the rear hatch is opened. It goes
off about 15 seconds after the door or rear hatch is closed.
However, the lamp goes off immediately in the following ca
Replacement of lamp bulbs
Before replacing a bulb, ensure the lamp is off. Do not touch the glass part
of the new bulb with your bare fingers; the skin oil left on the glass will evaporate
when the bulb gets hot and the vapor will condense on the reflector and dim the
surface.
Bulb capacity
A bulb should only be re
